Quick Send E-Mail. All repair manual spare parts catalog Diagnostic Software Diagnostic adapter interface. Have something to exchange? If you have a catalog, that we do not have in our list, we would gladly discuss the details of exchange or purchase.
Shop John Deere Service Advisor 5. All JD vehicles are covered. Completely offline windows desktop software. John Deere Service Advisor 5. Avoid switch from unleaded to regular gasoline to prevent engine damage.
Use of gasohol is acceptable as long as the ethyl alcohol blend does not exceed 10 per cent. Unleaded gasohol is preferred over leaded gasohol. Lift seat. Fill fuel tank at end of each day's operation. This helps to keep condensation out of fuel tank. TS NOV Use oil viscosity as shown on the temperature chart for the expected air temperature range during the drain interval.
SAE 90 oil is recommended in the differential. Other oils shown in the chart can also be used. DO NOT mix oils of different viscosities. X SEP Oil must be from a sealed plastic or all metal can to avoid any moisture. SAE 20 or 40 engine oil can also be used depending on temperature range during the service interval.
For complete repair information the component technical manual CTM is also required. Avoid fires due to smoking or careless maintenance practices.
Close fuel shut-off valve. Disconnect fuel line. Loosen cap screw and disconnect throttle cable. Remove electric PTO clutch. See Section 40, Group Depress clutch pedal and remove belt from idler wheel and drive sheave. Remove drive sheave A and key B.
Rotate engine to clear oil drain from hole in frame and remove engine. Adjust throttle cable, choke, governor, fast idle and slow idle.
See Section Disconnect throttle cable A. Relieve tension in traction belt for hydrostatic tractors. For gear driven tractors, depress clutch pedal. Remove belt from idler wheel and drive sheave. Remove four engine mounting cap screws. On gear driven tractors, remove belt guard A.
On gear driven units, remove belt guard A. Remove four cap screws and remove air duct. Disconnect spark plug wire. Remove two nuts and washers. Remove muffler. Put muffler and gasket into position. Install and tighten two washers and nuts. Disconnect spark plug wire and remove rubber grommet to remove spark plug wire from air duct. Remove four cap screws and two cap screws and nuts from air duct. First, remove right side of air duct A , then left side. Remove four cap screws and two spacers and remove muffler.
Position muffler and gasket. Install and tighten two spacers and four cap screws. Install left side of air duct, then right side. Put spark plug wire through hole in air duct and connect to plug. Install rubber grommet. Remove two nuts, washers and two cap screws A. Pull out on muffler guard and remove muffler. Position muffler and gasket by pulling out on muffler shield. Install and tighten two cap screws A , two nuts and washers.
Test fuel pump before removal. Disconnect vacuum line and fuel lines A and B. Remove cover, gaskets and diaphram. Make sure vent in cover is not plugged. Inspect diaphram for hairline cracks or wear. Remove valves by pulling rubber grommet. Inspect valves for hairline cracks or wear. Remove bottom diaphram and gasket. Inspect diaphram for holes, wrinkles or wear. Inspect all pump mounting surfaces. They must be free of any nicks or burrs.
Replace any worn or damaged gaskets or diaphragms. When installing inlet and outlet valve assemblies, use a punch or small dull shaft to stretch rubber grommet. Push stretched assembly into pump body. When assembling pump body, be sure flat area on bottom plate and pump body match.
Remove mower height knob, park brake knob A and transmission selector knob B. Remove pedestal shroud and platform. Disconnect fuel sensor wiring harness and remove it from foam pad. Check rubber bushings for leaks or damage.
Replace if necessary. See Disassemble Fuel Tank in this group. Make sure overflow tube A is not plugged. If equipped, pull fuel sensor from tank. Test fuel sensor. Push rubber bushing into tank. Push shut-off valve into housing. Push fuel sensor into rubber bushing.
Install tank. Put overflow tube through clip on back of frame. Put wiring harness under foam pad and connect harness to fuel sensor. Put platform on frame. Put seat switch connector through platform. Make sure all levers fit through platform. Install and tighten two nuts, washers and three cap screws. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. John Deere. You can help Turf Equipment Wiki by writing it. This article is too short to provide more than rudimentary information about the subject. You can help Turf Equipment Wiki by expanding it. Cancel Save. Fan Feed. Universal Conquest Wiki. Infobox incomplete The infobox for this article is missing infomation. Image needed This article and its infobox are missing images. Section needed This section is needed but has not been written yet.
0コメント