Lift the load lever. Push down the rear tab with your forefinger to bring the front end of the load plate up slightly. Open the load plate with thumb. Be careful not to touch the contacts. Hold CPU with thumb and forefinger. Ensure fingers align to socket cutouts. Match the CPU triangle marker to Pin 1 position as shown below.
The alignment key also provides the orientation directed function. Pin 1 position. After installing the CPU, remove the protective cover from load plate. The protective cover is used to protect the contacts of the socket. Do not discard the protective cover. Always replace the socket cover if the CPU is removed from the socket. Lower the lever and lock it to the load plate, then the CPU is locked completely.
Note :. Excessive temperatures will severely damage the CPU and system. Therefore, you should install CPU cooling fan and make sure that the cooling fan works normally at all times in order to prevent overheating and damaging to the CPU. Please refer to your CPU fan user guide to install it properly. This motherboard includes two pin slots for DDR2. You must install at least one memory module to ensure normal operation.
Mixed memory modules from different manufacturers is not recommended. There is only one gap near the center of the DIMM slot, and the memory module can be fixed in one direction only.
Unlock a DIMM slot by pressing the module clips outward. Warning :. Be sure to unplug the AC power supply before adding or removing expansion cards or other system peripherals, especially the memory devices, otherwise your motherboard or the system memory might be seriously damaged. This motherboard uses an ATX power supply.
In order to avoid damaging any devices, make sure that they have been installed properly prior to connecting the power supply. Make sure that the power supply cable and pins are properly aligned with the connector on the motherboard. Firmly plug the power supply cable into the connector and make sure it is secure. We recommend that you use W power supply or above.
If you want to use pin power supply, you need to align the ATX power connector according to the right picture. This connector accommodates a second serial port using an optional serial port bracket. Connect the bracket cable to this connector then install the bracket into a slot opening at the back of the system chassis.
This motherboard includes one connector for connecting the front panel switch and LED indicators. Attach the connector to the Reset switch on the front panel of the case; the system will restart when the switch is pressed. Attach the connector to the power LED on the front panel of the case. When the system is in S0 status, the LED is on. Attach the connector to the power button of the case. Pushing this switch allows the system to be turned on and off rather than using the power supply button.
The audio connector provides two kinds of audio output choices: the Front Audio, the Rear Audio. Their priority is sequenced from high to low Front Audio to Rear Audio. If headphones are plugged into the front panel of the chassis using the Front Audio , then the Line-out Rear Audio on the rear panel will not work.
If you do not want to use the Front Audio, pin 5 and 6, pin9 and 10 must be short, and then the signal will be sent to the rear audio port. This connector supports wireless transmitting and receiving device. Besides four USB ports on the rear panel, the series of motherboards also have two pin header on board which may connect to front panel USB cable to provide additional four USB ports.
These fans will be automatically turned off after the system enters suspend mode. These connectors support the thin Serial ATA cables for primary storage devices. The expansion cards can be installed in the two PCI slots. This motherboard has one PCI Express x16 slot that reserved for graphics or video cards. The difference in bandwidth between the x16 and x1 slot is notable to be sure. Before installing the expansion card, read carefully the documentation that came with it and make the necessary hardware settings for the card.
Make sure to unplug the power card before adding or removing any expansion cards. Um curto beep ser ouvido quando no for detectado nenhum problema na inicializao do seu sistema. Se algum problema for detectado o BIOS ir beepar em diferentes modos para indicar qual o problema. O LED ficar aceso enquanto o disco rgido estiver lendo ou gravando dados.
Pressione reset para reiniciar o computador se o sistema falhar ou travar. Pino 1 2 3 4 5 Este conector suporta dispositivos transmissores e receptores infravermelho sem fio. Pular no carrossel. Anterior no carrossel. Explorar E-books. Os mais vendidos Escolhas dos editores Todos os e-books. Explorar Audiolivros. Os mais vendidos Escolhas dos editores Todos os audiolivros.
Explorar Revistas. Escolhas dos editores Todas as revistas. Explorar Podcasts Todos os podcasts. Explorar Documentos. Enviado por Flavio Henrique de Oliveira. Denunciar este documento. Fazer o download agora mesmo. Grancursos Aula 1 Conceitos Basicos de Microinformatica Pesquisar no documento. Sergio Paulo Lima Bastos.
Ariel Garabetti. Especificaes tcnicas Ao conectar o painel do udio frontal, por favor, atente-se a configurao correta dos pinos e suas respectivas posies. Pular no carrossel. Anterior no carrossel. Explorar E-books. Os mais vendidos Escolhas dos editores Todos os e-books. Explorar Audiolivros. Os mais vendidos Escolhas dos editores Todos os audiolivros. Explorar Revistas. Escolhas dos editores Todas as revistas. Explorar Podcasts Todos os podcasts.
Explorar Documentos. MB Dis Pwgcx. Enviado por Nathan Pessoa. Denunciar este documento. Fazer o download agora mesmo. Salvar Salvar Mb Dis Pwgcx para ler mais tarde.
Manual de Servico Sky Ne Color-libre. Pesquisar no documento.
0コメント